Firmware and Software Update History

1. CR04 now supports displaying the MAC address of the WiFi module.
2. Fixed issue where CS107 would exit the group when updating group members in the app. This required synchronization optimization on the app side, but the updated app has not been launched yet.
3. Optimized the process of adding lights to prevent unknown networks from appearing.
4. When receiving the command to disable Bluetooth on RP1, an additional function has been added to prohibit mesh forwarding in conjunction with the existing disable feature.

1. When power is supplied to the Keilton+autani system, the luminaires activate.
2. Brightness test (5 seconds): Luminaires gradually increase to full brightness over 5 seconds.
3. Color temperature test (1 second): For luminaires with adjustable CCT (Correlated Color Temperature), the color shifts from warm to cool over 1 second.
4. Dimming test (5 seconds): Luminaires dim from full brightness over 5 seconds.
5. Final state: Luminaires return to full brightness with CCT set to a mid-level warmth. 

1. Optimized the mass production testing function of CS107D.
2. Added FlashNet functionality to emergency controller (OEM).
3. When modifying the method for calculating the threshold in the photocell, there were still some unresolved bugs in the code, but they have now been completely fixed.
4. Optimized the firmware of BCS107 to avoid the impact of the indicator LED on the functionality of the photo sensor.

1. Added the feature for motion status report.
2. Added the feature to enable/disable the flashnet reset (only for BLE5) so when sensors are commissioned it prevents sensor from being reset by flashnet.
3. Optimized the binding function for the Light Trace OEM emergency module. (only for BLE5)
4. The emergency module protocol adds a new error code for timestamp anomalies (only for BLE5).
5. The up and down lighting fixtures have added support for scene and testing switches (only for BLE5).
6. The minimum voltage value for the photo sensor ADC sampling has been changed from the default value to real-time sampling (only for BLE5).
7. Optimized the write/erase protection measures for special parameters (only for BLE5).
8. Optimized the impact of hardware & housing changes on the BCS107 light sensor, and the issue of the BCS107’s motion sensor is always in an occupied state (only for BLE5).

1. Added the feature for motion status report.
2. Added the feature to enable/disable the flashlight. (only for BLE5)
3. Optimized the binding function for the Light Trace OEM emergency module. (only for BLE5)

Improvement to mesh OTA process to increase the success rate of mesh OTA for huge quantity nodes (more than 2000 nodes).

1. Disable local motion sensor feature, in case the sensor is installed in places that may cause motion trigger, such as near HVAC.
2. Support for DALI commands (only for BLE5).

Firmware release 240615:
1. Flashlight aided commission, devices with photo sensor can be commissioned with flashlight.
2. CR02-W indicator update: 1Hz flash when in factory setting; 0.25Hz flash when commissioned.
3. Update of CR05 to include motion status report.
4. Up and down light firmware with sensor ready feature.

1. While flashing to indicate successful operations, sensors dim between 100% and 10%, instead of 100% and OFF, to avoid causing panic by turning off all fixtures.

1. CS107D manual off override bug fix.

1. Bug fix: when enabling motion by schedule, the sensor won’t start motion trigger cycle immediately.
2. Manual off override is added to CS107.

1. Bug fix: when enabling motion by schedule, the sensor won’t start motion trigger cycle immediately.
2. Manual off override is added to CS107.

Improvement to commission performance, increased the success rate for receiving commission messages from APP.
Emergency lighting test report log improvement, adding test type to the log.
Litetrace CS107 firmware release.

1. Improve the ‘manual off override’ feature on BLE4.2 modules.
2. Add daylight harvesting support for ceiling sensors.

Lowbay sensor with high sensitivity PIR motion detection algorithm.

1. While flashing to indicate successful operations, sensors dim between 100% and 10%, instead of 100% and OFF, to avoid causing panic by turning off all fixtures.

1. CS107D manual off override bug fix.

1. Bug fix: when enabling motion by schedule, the sensor won’t start motion trigger cycle immediately.
2. Manual off override is added to CS107.

1. Bug fix: when enabling motion by schedule, the sensor won’t start motion trigger cycle immediately.
2. Manual off override is added to CS107.

Improvement to commission performance, increased the success rate for receiving commission messages from APP.
Emergency lighting test report log improvement, adding test type to the log.
Litetrace CS107 firmware release.

1. Improve the ‘manual off override’ feature on BLE4.2 modules.
2. Add daylight harvesting support for ceiling sensors.

Lowbay sensor with high sensitivity PIR motion detection algorithm.

1. Improvement to CS107S / CS107D for bi-level dimming performance.
2. Manual off override feature for occupancy sensors.
3. Emergency driver controller.
4. Improve the astronomical clock accuracy from 15 minutes to 5 minutes.
5. Improve commission performance to avoid duplicate IDs.
6. IWS102 wall sensor switch firmware.
7. Improvement to 485 bridge.

Astronomical clock, and schedules based on sunrise/sunset time.

Improvement to CS107S/D to support SCENE, bi-level dimming.

Support for RP1 commission tool.

1. Improved daylight harvesting strategy, dim up/dim down to have different speeds to provide a better experience.
2. Improved High Bay PIR sensor response time.

New firmware for ceiling sensor to provide bi-level dimming function.

Daylight harvesting strategy. Allows user to choose from aggressive/mild/soft daylight harvesting strategy to maximize energy savings or to provide more comfortable lighting. User may also fine-tune daylight harvesting parameters to better match the project requirements.

From user feedback. App disables daylight harvesting by default. Avoids annoyance of lighting automatically dimming up and down in response to daylight sensors. Users may still enable daylight harvesting if desired.

Increases the performance of High Bay PIR sensors which can detect motion, turning on lights more quickly.

Scheduled daylight harvesting calibration. Allows user to schedule a daylight harvesting calibration routine during the nighttime hours for optimal setting without requiring user to be on job site at night.

Enable stepless CCT tuning and 4 pre-set CCT selections for integrated 4 CCT modules.

User may directly input on/off threshold value for PC sensors without calibration.

Increase the startup speed when motion is detected.

Sensors may switch between Occupancy/Vacancy mode. User may easily switch the function on the APP. This allows more flexibility of the function to meet the regulation requirement.

Firmware for new product PPA109S, an UL924 compliant Emergency Lighting Control Device which can work together with Keilton controllers and sensors to provide emergency lighting control upon normal power interrupt.

1. Update the flash indication: when updating group/schedule settings, only the luminaire in the group/schedule will flash. Previously, all luminaires in the ZONE would flash, which may annoy users in retrofit projects where the site is already in use.
2. Firmware update to support enable/disable motion/photo sensor by schedules.
3. Firmware update to support CR03 Remote Access Bridge / CR04 Inter-Op Bridge.

Firmware for new product, WF20R, a 20A wall receptacle which can be controlled by Keilton APP and linked with Keilton sensors.

Firmware for new product, CR04 Inter-Op Bridge, a dongle with WIFI connection, providing Modbus TCP and REST API for 3rd party inter-operation, such as BACnet, OpenADR.

Line voltage key pad with 7 keys: ON/OFF, dim up, dim down, and 4 scene keys.